Complete brake set from brake calliper and brake line to the master pump for the foot brake.
Ideal for equipping your moped with a disc brake system on the rear wheel.
In order to be able to fit this brake system to your bike, various adjustments are required. However, this should not be a problem for experienced mechanics.
High-quality components made of solid cast aluminum and a steel flex brake line.
The line has already been filled with brake fluid and is therefore ready for immediate use, but we recommend bleeding the system after installation.
A switch for the brake light is attached to the brake master cylinder.
Brake line length: 260 mm
Distance between mounting holes for brake master: 40.5 mm
Distance between mounting holes for brake calliper: 60 mm
All AJP brake pads can be installed in this disc brake calliper.
You can find a selection of these and other add-on parts such as brake fluid, brake disc, brake hose, etc. in the accessories section.
Details
| Mounting type | Screws |
| Hole spacing | 40.5 mm, 60 mm |
| Cable length | 260 mm |
Accessories & related products
Motorex brake fluid DOT4 250 ml
Manufacturer: Motorex · DOT class (brake fluid): DOT 4 (230°C) · Contents [ml]: 250 ml · Hazard warning: Can harm the child in the womb · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS08 - Harmful to health · Area of application: Standard
CHF 8.70
CHF 34.80/l
Moped fans like you also bought:
swiing® ingenious pull starter Bosch / Ducati | Puch E50
Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Color: Chrome · Color: black-matt · Ignition system: BOSCH · Ignition system: DUCATI · Width: 150 mm · Ø outside: 130 mm · Total length: 160 mm · Height: 88 mm · Number of fixing points: 2 pcs · Hole spacing: 137.5 mm
CHF 149.90
Not so nice 
Road Master 2.25 x 17" F-323 4.P.R. Allround
Manufacturer: Road Master · Tire width [inch]: 2.25 " · Color: black · Width [inch]: 2 1/4 · Wheel size [inch]: 17 " · Old designation: 21 x 2.25 · Speed index: B = 50 km/h · Load capacity index: 39 = 136 kg · Profile type: F-323 4.P.R. · Tire type: Allround · White wall: No · Tubeless (yes/no): Tubetype TT (requires hose)
CHF 29.90
GPO Brake support bolt short Inox | Puch Maxi, Supermaxi
Manufacturer: GPO · Material: Chrome steel (stainless steel) · Thread type: MF10x1 (fine pitch thread) · Ø shaft: 9.8 mm · Drive: Outer edge · Total length: 32 mm · Thread length: 13 mm · Ø External head: 14 mm · Area of application: Standard · Shank: Yes · Number of components: 3 pcs · Shank length: 9.5 mm · Width across flats SW: 13 mm · Width across flats SW: 17 mm
CHF 12.90
Hot 
Jammer racing clutch special 65 ccm and more | Puch E50
Manufacturer: Jammer · Material: Steel · Surface: galvanized (blue) · Material addition: Steel · Recording type: Cone mounting · Number of jaws: 3 pcs · Ø outside: 92.5 mm · Number of springs: 3 pcs · Thickness: 19 mm · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning
CHF 189.90
Not in stock
Hot
swiing 15 mm carburetor tuning camouflaged | Puch
Manufacturer: swiing · Material: Aluminum · Mounting type: Plug connection clamped · Carburetor type: SRE · Width: 50 mm · Nozzle thread: M3.5x0.6 (standard thread) · Ø fuel hose connection: 6 mm · Nominal diameter: 15 mm · Ø Internal connection: 20 mm · Total length: 66 mm · Nozzle size: 62 · Ø Inside entrance: 15 mm · Height: 95 mm · Area of application: Tuning · Ø Output inside: 15 mm · Ø Air filter connection: 20 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle block: 2.17 · Camouflaged: Yes · Clamping screw torque (max.): 4 N/m
CHF 79.90
swiing® revival 12 mm carburetor (original) | Puch
Manufacturer: swiing® revival parts · Material: Aluminum · Color: gray · Mounting type: Plug connection clamped · Carburetor type: SRE · Width: 50 mm · Nozzle thread: M3.5x0.6 (standard thread) · Ø fuel hose connection: 6 mm · Nominal diameter: 12 mm · Ø Internal connection: 20 mm · Total length: 65 mm · Nozzle size: 52 · Ø Inside entrance: 12 mm · Height: 108 mm · Area of application: Standard · Ø Output inside: 12 mm · Ø Air filter connection: 20 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle block: 2.15 · Camouflaged: No · Clamping screw torque (max.): 4 N/m
CHF 69.90
Collection only possible with online purchase and appointment.
