Clutch drum of the Primärantrieb for 2-speed manual Z50 engines of Puch X30 NS, NL mopeds / mopeds.
This clutch basket is used in combination with primary drive sprockets, which have 69 teeth.
Number of teeth: 19
Toothing: helical
Total height: 26.6 mm
Number of plates: Double-disc clutch
You can find the sliding blocks, thrust washers and other parts in the accessories section.
Original Puch spare part number: 350.1.12.002.2
Details
| Ø inside | 19.44 mm |
| Ø outside | 28.1 mm |
| Manufacturer | HS-Retro |
| Material | Steel |
| Surface | hardened & ground |
| Area of application | Original, High End |
| Width | 7.5 mm |
| Puch spare part no. | 329.1.13.010.1 |
Suitable for the following models
| Puch | Z50 (X30 Sport) |
Accessories & related products
HS-Retro bearing ring 24/32/7.5 large Z50 (1A quality) | Puch X30 NS, NL
Ø inside: 23.8 mm · Ø outside: 31.98 mm · Manufacturer: HS-Retro · Width: 7.55 mm · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Puch spare part no.: 329.1.13.065.1
CHF 58.70
Moped fans like you also bought:
swiing® revival gasket set Z50 engine | Puch X30 NS / NL
Manufacturer: swiing® revival parts · Material: Sealing paper · Area of application: Standard · Number of components: 10 pcs · Ø outlet inside: 22 mm · Hole spacing inlet: 32 - 38 mm · Hole pattern [mm]: 44 x 44 · Hole spacing outlet: 42 mm
CHF 19.90
swiing® revival shim set crankshaft L17 | Puch Z50
Nominal diameter: 17 mm · Ø inside: 17.1 mm · Ø outside: 23.8 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.25 mm · Thickness: 0.3 mm
CHF 8.90
Jasil full cheek crankshaft (+2 mm stroke) | Puch X30 NS / NL & Velux (Z50)
Manufacturer: Jasil · Weight: 930 g · Material: Aluminum · Area of application: Performance · Area of application: Racing · Material: Steel · Area of application: Tuning · Cheek type: Full cheeks · Crankshaft stroke: 45 mm · Ø piston pin (B): 12 mm · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 57 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 14 mm · Length 2nd paragraph: 15 mm · Length 3rd paragraph: 10 mm
CHF 199.90
HS-Retro bearing ring 24/32/7.5 large Z50 (1A quality) | Puch X30 NS, NL
Ø inside: 23.8 mm · Ø outside: 31.98 mm · Manufacturer: HS-Retro · Width: 7.55 mm · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Puch spare part no.: 329.1.13.065.1
CHF 58.70
Collection only possible with online purchase and appointment.
