Nos
Hot 
Rear wheel hub for spoke rims of Puch Maxi S / N and Puch X30 Sport NG-2A mopeds / mopeds.
The bearing shells are already pressed in and still lubricated with old grease from back then.
These ultra-rare hubs are from old stock and have been stored relatively poorly. Corrosion and occasional scratches are therefore guaranteed to occur!
However, these relics from the past are the ideal basis for polishing or fresh painting.
Corresponding add-on parts such as wheel axle, wheel nuts, freewheel, brake anchor plate, brake pads etc. can be found in the accessories section.
NOS – New from old stock.
Original Puch spare part number: 349.5.41.803.1
Details
| Manufacturer | Puch |
Suitable for the following models
| Puch |
Accessories & related products
swiing® ingenious rear wheel axle Ø 29 mm conversion kit with ball bearings | Puch
Ø inside: 12 mm · Ø outside: 29 mm · Manufacturer: swiing® ingenious parts · Thread length: 29 mm · Thread length: 53 mm · Material: Steel · Surface: blue galvanized · Diameter: 29 mm · Total length: 190 mm · Ø shaft: 19 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 100 mm · Ball bearing closed: Yes · Width across flats SW: 19 mm
CHF 38.90
swiing® revival rear brake anchor plate | Puch Maxi N
Material: Steel · Surface: blue galvanized · Total length: 135 mm · Manufacturer: swiing® revival parts · Ø outside: 92 mm · Ø axle: 12 mm · Ø External brake pads: 80 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Brake lever length (lever length): 68 mm · Cranking (offset): 10 mm · Ø screw holder: 6.5 mm
CHF 74.90
ESJOT freewheel 23 teeth (1A quality)
Material: Steel · Surface: Hardened · Color: silver · Thickness: 15 mm · Manufacturer: ESJOT · Chain pitch: 1/2" x 1/8" · Number of teeth: 16 pcs · Number of teeth: 18 pcs · Number of teeth: 20 pcs · Number of teeth: 23 pcs · Thread type: FG34.8 (1.37" 24G)
CHF 14.90
Moped fans like you also bought:
swiing® revival upright spring blue galvanized | Puch
Spring design: Tension spring · Ø wire: 2.5 mm · Length spring hook: 19 mm · Length spring hook: 53 mm · Manufacturer: swiing® revival parts · Material: Spring steel · Surface: blue galvanized · Total length: 122 mm · Ø inside: 9 mm · Ø outside: 14 mm
CHF 2.70
swiing® ingenious needle roller bearing 12/15/16.2 "Racing" silver cage
Bearing cage: Silver cage · Width: 16.2 mm · Manufacturer: swiing® ingenious parts · Ø outside: 15 mm · Bearing type: Needle roller and cage assembly · Ø inside: 12 mm · Dimension needle bearing: 12/15 x 16.2 · Tomos spare part no.: 035548
CHF 13.90
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Material: Plastic · Material: Steel · Surface: blank · Bearing cage: "-" Sheet steel cage ball-guided · Width: 9 mm · Inner ring width: 9 mm · Manufacturer: swiing® ingenious parts · Ø outside: 29.02 mm · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Ball bearing closed: Yes
CHF 8.90
MBR piston 46.93 mm Gilardoni italkit | Puch
Nominal diameter: 47 mm · Surface: molybdenum-coated · Manufacturer: MBR · Manufacturer: Wössner · Ø outside piston (A): 46.93 mm · Compression height (C): 22 mm · Curvature (D): 2.65 mm · Total piston height (E): 48.15 mm · Number of piston rings (F): 1 pcs · Piston ring mold: Rectangular ring · Piston ring impact: Internal fuse (IS) · Piston ring height: 1 mm · Ø piston pin (B): 12 mm
CHF 118.90
Collection only possible with online purchase and appointment.
