Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and fan wheel. Suitable for your Sachs moped / moped with 502, 50/2, 50/3, 50/4 engine and fan cooling.
The racing ignition comes complete with CNC-milled fan wheel and constantly supplies your cylinder with the optimum cooling.
The small rotor results in better acceleration and throttle response. If you want an even smoother idle, you can order the additional weight (optional) at the same time.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, therefore smoother engine idling (382 grams)
- Fine balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- Optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set the piston to TDC, the marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing point of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel; this achieves a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good ground (earthing), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal plug:
- 1 = black
- 2 = blue
- 3 = white
Attention: Under no circumstances should excessively long screws be used to mount the fan wheel, as otherwise the stator winding may be damaged. A suitable screw set is included in the scope of delivery.
When you purchase this complete set, you will receive a substantial percentage off the retail price of the individual parts.
The ignition is compatible with cable starters, which also fit the HPI, you can find these in the accessories section.
Exclusive product for the highest demands of the quality brand swiing®.
The set includes the following fixed parts:
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: black · Ø outside: 110 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Number of fixing points: 6 pcs · Height: 25 mm · Weight: 116 g · Alternative version of the Pony Spare part no.: A1026 · Alternative version of Sachs spare part no.: 0211 070 105
Manufacturer: swiing® revival parts · Material: Chrome steel (stainless steel) · Thread type: M6x1 (standard thread) · Drive: Slot · Number of components: 6 pcs
Manufacturer: swiing® ingenious parts
Details
| Manufacturer | swiing® ingenious parts |
| Ø Internal flywheel | 63.5 mm |
| Light coil voltage | 12 V |
| Tension | 12 V |
| Performance | 60 W |
| Direction of rotation | any |
| Ø mounting plate | 90 mm |
| Ø Flywheel outside | 75 mm |
| Area of application | Tuning, High End, Racing |
| Mounting type | Screws |
| Number of fixing points | 3 pcs |
Suitable for the following models
| Sachs | 502 (Saxonette) - AL, AML 50/2 - L CH (0.8 PS), ML CH (0.8 PS), MB (2.6 PS), MLB (2.6 PS) 50/3 50/4 - MLFB (2.6 PS), LKH (4.5 PS) |
Accessories & related products
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Ø cable: 5 mm · Ø cable: 7 mm · Pony spare part no.: A2099 · Sachs spare part no.: 0265 100 00
CHF 8.75
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Beta 521
Width across flats (trigger): 27 mm · Manufacturer: GPO · Clamping depth: 10 mm · Number of components: 1 pcs · Material: Steel · Surface: blackened · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Area of application: (Dis)assembly tool · Width across flats Screw: 19 mm · Total length: 55 mm · Total length: 75 mm · Strength class: 8.8
CHF 9.90
Hot 
Leonelli 12V voltage regulator (1A quality)
Width: 27 mm · Height: 15 mm · Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: blue galvanized · Tension: 12 V · Type of current: Alternating current (AC) · Performance: 100 W · Ø mounting hole: 6 mm · Mounting type: Screws · Total length: 50 mm
CHF 34.90
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Type of application: 1K · Area of application: Chemistry · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Contents [ml]: 10 ml · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
CHF 21.90
CHF 2’190.00/l
swiing® ingenious fan wheel red (EVO, HPI, Bosch, Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Ø inside: 39 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Color: red · Surface: anodized · Weight: 87 g · Height: 13.5 mm · Ø outside: 120 mm · Number of fixing points: 10 pcs · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm
CHF 62.40
swiing® ingenious fan wheel chrome (EVO, HPI, Bosch, Ducati) | Puch X30 Velux, Sachs 503, Belmondo
Ø inside: 39 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Color: Chrome · Surface: chrome-plated · Weight: 87 g · Height: 13.5 mm · Ø outside: 120 mm · Number of fixing points: 10 pcs · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm
CHF 68.90
DENSO (IWF24 / IWF27) Spark plug short thread U-Groove Iridium
Manufacturer: DENSO · Area of application: Cross · Area of application: High End · Area of application: Tuning · Candle thread type: short · Spark plug socket: M4 · Electrode material: Iridium · Suppressed: No · Width across flats SW: 21 mm · Thread type: MF14x1.25 (fine pitch thread)
CHF 25.90
swiing® ingenious 280 g additional weight EVO Inox
Manufacturer: swiing® ingenious parts · Material: Chrome steel (stainless steel) · Area of application: Tuning · Surface: electropolished · Thickness: 12 mm · Ø bolt circle: 48 mm · Ø bolt circle: 54 mm · Ø outside: 95 mm · Ø inside: 39 mm · Number of fixing points: 3 pcs · Weight: 280 g · Ø mounting hole: 6.2 mm
CHF 49.90
Moped fans like you also bought:
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Ø cable: 5 mm · Ø cable: 7 mm · Pony spare part no.: A2099 · Sachs spare part no.: 0265 100 00
CHF 8.75
Hot
Leonelli 12V voltage regulator (1A quality)
Width: 27 mm · Height: 15 mm · Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: blue galvanized · Tension: 12 V · Type of current: Alternating current (AC) · Performance: 100 W · Ø mounting hole: 6 mm · Mounting type: Screws · Total length: 50 mm
CHF 34.90
swiing® ingenious fan wheel black (EVO, HPI, Bosch, Ducati) | Sachs 50/2, 50/3
Ø inside: 39 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Color: black · Surface: anodized · Weight: 116 g · Height: 25 mm · Ø outside: 110 mm · Number of fixing points: 6 pcs · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Alternative version of the Pony Spare part no.: A1026 · Alternative version of Sachs spare part no.: 0211 070 105
CHF 59.90
swiing® ingenious cylinder head gasket 41 mm | Sachs 503, 502, 50/2, 50/3, 50/4
Nominal diameter: 41 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Place of use: Cylinder head · Ø cylinder: 41 mm · Area of application: Standard · Thickness: 0.3 mm · Ø inside: 41.7 mm · Hole pattern [mm]: 37 x 37
CHF 4.90
Not in stock
Collection only possible with online purchase and appointment.
