Ready-to-install cable starter for all Piaggio Ciao moped / moped models with mono and variomatic drive.
The Swiss-made pull starter is designed for the highest loads and has proven itself in racing.
Assembly:
1. Starter pinion: Clean the mounting surfaces, then screw the counterpart for the pull starter onto the clutch or Variomat (secure the enclosed flange nut with Loctite).
2. Pull starter: Lightly fasten the housing adapter using the engine screws. Then fit the round housing with the pull-wire starter unit and secure with the enclosed M5 x 45 mm screws. Finally, tighten the engine screws.
Application:
1. Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
2. Pull out the cable starter handle until it engages fully and meets with resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests or a pedal axle extension must be fitted.
Further helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
The set includes the following fixed parts:
Manufacturer: swiing® ingenious parts · Material: Steel, Aluminum, Plastic · Surface: anodized · Color: black, silver · Ø outside: 115 mm · Number of fixing points: 3 pcs · Hole spacing: 75 mm, 78 mm · Height: 103 mm · Total length: 160 mm · Width: 135 mm
Details
| Width | 135 mm |
| Ø outside | 115 mm |
| Height | 103 mm |
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Aluminum, Plastic |
| Surface | anodized |
| Color | black |
| Total length | 160 mm |
| Hole spacing | 75 mm, 78 mm |
| Number of fixing points | 3 pcs |
Suitable for the following models
| Piaggio | Ciao - Ciao, Ciao, Ciao, Ciao |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Type of application: 1K · Area of application: Chemistry · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Contents [ml]: 10 ml · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
CHF 21.90
CHF 2’190.00/l
Screw M5x45 cylinder head Allen key galvanized
Material: Steel · Surface: blue galvanized · Total length: 50 mm · Drive: Hexagon socket · Thread length: 22 mm · Screw head: Cylinder head · Ø External head: 8.5 mm · Shank: Yes · Strength class: 8.8 · Thread type: M5x0.8 (standard thread) · Shank length: 23 mm
CHF 2.00
swiing® ingenious cable starter red | Piaggio Ciao
Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Plastic · Material: Steel · Surface: anodized · Color: black · Color: red · Ø outside: 115 mm · Number of fixing points: 3 pcs · Hole spacing: 75 mm · Hole spacing: 78 mm · Height: 103 mm · Total length: 160 mm · Width: 135 mm
CHF 199.00
Not in stock
Moped fans like you also bought:
swiing nozzle set M3.5 (64 - 74) Bing SRE, SRA, SRC, SRF
Manufacturer: swiing · Material: Brass · Quantity: 6 pcs · Carburetor type: SRA (1/11/31) Velux · Carburetor type: SRA (1/11/35) Velux · Carburetor type: SRC · Carburetor type: SRE · Carburetor type: SRF · Nozzle type: Main nozzle · Drive: Slot · Total length: 6 mm · Nozzle thread: M3.5 · Nozzle size: 64 · Nozzle size: 66 · Nozzle size: 68 · Nozzle size: 70 · Nozzle size: 72 · Nozzle size: 74
CHF 15.90
swiing nozzle set M5 (70 - 92) Dell'Orto SHA, PHBG
Manufacturer: swiing · Material: Brass · Quantity: 10 pcs · Carburetor type: PHBG · Carburetor type: SHA (type 3) · Carburetor type: SHA (type 4) · Total length: 8 mm · Nozzle type: Main nozzle · Drive: Slot · Nozzle thread: M5 · Nozzle size: 70 · Nozzle size: 72 · Nozzle size: 75 · Nozzle size: 78 · Nozzle size: 80 · Nozzle size: 82 · Nozzle size: 85 · Nozzle size: 88 · Nozzle size: 90 · Nozzle size: 92
CHF 20.90
Not in stock
Collection only possible with online purchase and appointment.
