Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with an original Bosch / Ducati ignition.
Made in Switzerland. Designed for the highest loads and proven in racing.
Fitting:
1. Starter pinion: Clean the flywheel, then screw the counterpart for the cable starter onto the pole wheel (secure with Loctite).
2. Pull-wire starter: Position the starter housing correctly and tap lightly with a plastic hammer until the pull-wire starter is perfectly seated. It can then be screwed into place.
Application:
1. Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
2. Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Other helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber mallet etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
Details
| Color | Chrome, black-matt |
| Ø outside | 130 mm |
| Total length | 160 mm |
| Width | 150 mm |
| Height | 88 mm |
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Surface | chrome-plated |
| Ignition system | BOSCH, DUCATI |
| Hole spacing | 137.5 mm |
| Number of fixing points | 2 pcs |
Suitable for the following models
| Puch | E50 |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Color: blue · Contents [ml]: 10 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Area of application: Chemistry · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
CHF 21.90
CHF 2’190.00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Total length: 257 mm · Manufacturer: GPO · Material: Steel · Surface: chrome-plated · Color: Chrome · Chain pitch: 1/2" x 3/16" · Ø outside: 15.9 mm · Number of teeth: 28 pcs · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
CHF 59.90
IXS motorcycle gloves Skull S black
Manufacturer: IXS · Test mark: EN13594:2015 · Material: Polyester (PES) · Color: black · Color: white · Gender: Unisex · Size: L · Size: S · Hand circumference: 21 - 22 cm · Hand circumference: 22 - 23 cm · Hand circumference: 23 - 24 cm · Hand circumference: 24 - 25 cm
CHF 41.80
Moped fans like you also bought:
Airsal 44 mm cylinder kit 65 ccm camouflaged | Puch
Manufacturer: Airsal · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Displacement: 65 ccm · Ø cylinder neck: 48 mm · Nominal diameter: 44 mm · Ø piston pin (B): 12 mm · Inlet window: 24 / 20 x 15 · Thread inlet: M6x1 (standard thread) · Ø outlet inside: 25 mm · Number of fixing points: 4 pcs · Hole spacing outlet: 42 mm · Area of application: Tuning · Outlet type: straight · Hole spacing inlet: 38 mm · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Camouflaged: Yes
CHF 84.90
Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing
Ø Stranded wire: 1.25 mm · Nipple shape: Cylinder · Ø nipple: 3 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Cable length: 2200 mm · Nipple length: 5 mm · Area of application: Standard · Number of components: 1 pcs
CHF 2.80
Magura gas cable clamp / deco cable clamp Ø 5 x 6 mm
Manufacturer: Magura · Material: Brass · Material: Steel · Thread type: M4x0.7 (standard thread) · Surface: nickel-plated · Ø Cable bushing: 1.6 mm · Drive: Slot · Ø outside: 5 mm · Total length: 6 mm · Screw head: Lens head · Thread length: 4 mm · Number of components: 2 pcs
CHF 2.00
Motorex Automatic Motor Oil (ATF) 450 ml
Temperature resistance (min.): -45 - 200 °C · Manufacturer: Motorex · Contents [ml]: 450 ml · Gearbox type: Automatic machine · Area of application: Gearbox lubrication with clutch · Pony OEM number: A2080 · Sachs OEM number: 0263 014 002
CHF 9.90
CHF 22.00/l
GPO 44 mm cylinder head tuning | Puch Maxi S, N / X30 NS, NL, N-2AH
Manufacturer: GPO · Material: Aluminum · Surface: sandblasted · Width: 125 mm · Total length: 135 mm · Ø cylinder: 44 mm · Height: 55 mm · Candle thread: short · Number of fixing points: 4 pcs · Area of application: Tuning · Hole pattern [mm]: 44 x 44 · Decompressor: No · Camouflaged: Yes
CHF 42.90
Collection only possible with online purchase and appointment.
