Crankshaft suitable for all Piaggio moped and moped models (Ciao, Si, Bravo, Boxer, Grillo).
This finely balanced crankshaft fits all cylinders with 10 mm piston pin and impresses with its high-quality workmanship.
Connecting rod eye (A): 13.0 mm
Ø bearing seat right (B): 15.0 mm
Ø bearing seat rear (C): 15.0 mm
Stroke (2xD): 43.0 mm
Sleeve length (E): 87.0 mm
Width of crank webs (F): 33.0 mm
1st shoulder (G): 21.0 mm
2nd shoulder (H): 44.0 mm
3rd shoulder (I): 63.5 mm
Total length crankpin end (J): 90.0 mm
Ø Vario / clutch pin (H): 12.0 mm
Dimension needle bearing: Ø 10 / 13 x 14.2 mm (axe 10)
Thread: M8 x 1.25 mm
For installation, a 16 x 0.5 mm shim must be inserted between the standard crankshaft and its main bearings.
The corresponding spacers can be found in the accessories section.
Original Piaggio spare part number: 1841545
Quality product from the Italian manufacturer Mazzucchelli.
Details
Dimension needle bearing | 10 / 13 x 14.2 mm (axe 10) |
Manufacturer | Mazzucchelli |
Material | Steel |
Cheek type | standard |
Area of application | Standard, Original |
Crankshaft stroke | 43 mm |
Ø coupling pin / vario pin | 12 mm |
Connecting rod length center-center | 87 mm |
Thread type | M8x1.25 (standard thread) |
Total length crankpin ignition side | 90 mm, 106 mm |
Ø crank webs | 69.7 mm |
Thread length | 16 mm |
Ø Connecting rod eye | 13 mm |
Bearing seat right | 15 mm |
Ø piston pin (B) | 10 mm |
Weight | 695 g |
Ø Bearing seat (ignition side) | 15 mm |
Wide crank webs | 33 mm |
Length 1st paragraph | 21 mm |
Length 2nd paragraph | 44 mm |
Length 3rd paragraph | 63.5 mm |
Ø 1st step (on the coupling side) | 15 mm |
Ø 2nd shoulder (on the clutch side) | 14.4 mm |
Ø 3rd step (on the clutch side) | 12 mm |
Inlet control time | 130 ° |
Control time before O.T | 77 ° |
Control time according to O.T | 53 ° |
Number of gears | 1 pcs |
Suitable for the following models
Piaggio | Ciao - Ciao, Ciao, Ciao, Ciao Si Bravo/Superbravo Boxer Grillo |
Accessories & related products
swiing® ingenious puller flywheel | Piaggio Ciao, SI, Bravo, Boxer
Total length: 100 mm · Width across flats (trigger): 10 mm · Width across flats (trigger): 18 mm · Manufacturer: swiing® ingenious parts · Width across flats Screw: 19 mm · Material: Steel · Surface: blackened · Surface: blue galvanized · Number of components: 2 pcs · Area of application: (Dis)assembly tool · Diameter: 12 mm · Diameter: 24 mm · Thread type: MF12x1.5 (fine pitch thread) · Thread type: MF17x1 (fine pitch thread)
CHF 17.90
Moped fans like you also bought:
EFFE Condenser with cable | Piaggio Ciao, SI, Bravo, Boxer
Height: 26 mm · Manufacturer: EFFE · Ø mounting hole: 4.4 mm · Capacity: 0.26 µF · Area of application: Original · Area of application: Standard · Mounting type: Tab for screwing · Connection type: Cable for screwing · Ø outside: 18 mm · Piaggio spare part no.: 102939
CHF 11.90
SKF 6202 C3 ball bearing 15/35/11
Bearing cage: "-" Sheet steel cage ball-guided · Width: 11 mm · Stock number: 6202 · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: C3 · Bearing type: Deep groove ball bearing · Ø inside: 15 mm · Ø outside: 35 mm · Puch spare part no.: 900.4.6202
CHF 9.90
swiing® revival gaskets & oil seals engine | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: NBR · Material: Oiled paper · Number of components: 3 pcs · Piaggio spare part no.: 112967 · Piaggio spare part no.: 182519 · Piaggio spare part no.: 480464
CHF 11.40
Not in stock