Screw-toothed driver pinion made of hardened steel for the KTM SX50 clutch on the Puch E50 single-automatic engine of your Puch Maxi S, N and Supermaxi LG1 moped / moped.
Either an E50 kickstarter engine must be used or a similar E50 roll-on engine must be fitted with a kickstarter cover.
You can find the corresponding conversion kit in the accessories section.
The nut is screwed onto the clutch hub and locked with the grub screw. This should be fitted with Loctite threadlocker.
Thread: M10 x 1 mm
Wrench width SW: 17 mm hexagonal
Tightening torque for driver pinion: 35 - 40 Nm
Tightening torque for grub screw: 10 Nm
It is essential to check whether the distance between the driver pinion and the gearbox cover is large enough to prevent the teeth from rubbing against each other when idling. If the latter is the case, the corresponding dimension must be turned off on the clutch side of the driver pinion.
Corresponding attachments such as Loctite, gearbox cover, SX50 clutch, assembly tool, etc. can be found in the accessories section.
Details
| Manufacturer | MBR |
| Material | Metal |
Suitable for the following models
| Puch | E50 |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Contents [ml]: 10 ml · Area of application: Chemistry · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Temperature resistance (min.): -75 - 200 °C · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
CHF 21.90
CHF 2’190.00/l
MBR Clutch KTM SX50 | Puch E50
Manufacturer: MBR · Material: Steel · Material addition: Aluminum · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs
CHF 342.80
Moped fans like you also bought:
swiing® ingenious crankshaft High End (Version 2.0) | Puch E50
Manufacturer: swiing® ingenious parts · Thread length: 11 mm · Thread length: 15 mm · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Area of application: High End · Area of application: Racing · Area of application: Tuning · Crankshaft stroke: 43 mm · Ø piston pin (B): 12 mm · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Thread type: MF10x1 (fine pitch thread) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Weight: 968 g · Ø 3rd step (on the clutch side): 15 mm · Number of gears: 1 pcs
CHF 136.60
Collection only possible with online purchase and appointment.
