Shaft repair sleeve which can be used on worn, scratched or run-in areas, e.g. on the crankshaft or pinion shaft.
If a shaft is heavily run-in or scratched and can therefore no longer be properly sealed by the oil seal, this Speedi-Sleeve repair sleeve is used.
The 0.2 mm thick chrome steel sleeve is pressed over the shaft using the tool supplied.
Because the shaft is only applied a little, an oil seal with the original dimensions can still be used.
Shaft diameter: 15.0 mm
Width of usable running surface: 5 mm
Material: special, polished chrome steel
Installation instructions:
- Before installation, remove the crankshaft bearing if necessary. If necessary, mount the crankshaft bearing on the shaft, as this can no longer be pressed over the sleeve later.
- Clean the seal sliding surface on the shaft. Remove any unevenness with an abrasive cloth; the sleeve must not be positioned over keyways, holes, threads or other recesses
- Determine the installation position of the repair sleeve on the worn seal sliding surface and mark it precisely. The sleeve must completely cover the damaged area.
- Drive the repair sleeve onto the shaft with light, centric strokes against the impact cap. If the impact cap is too short, a piece of pipe can be used instead. The inside diameter should correspond to that of the impact cap. Ensure that the functional surface of the sleeve is not damaged.
- Do not use any heat during assembly; the use of adhesive is not necessary.
- In the case of large grooves or notches, the sleeve can be pressed on together with some permanently elastic sealing compound.
- If necessary, the flange can be removed by slitting the outer part and using needle-nose pliers.
- Then check everything again for damage and any burrs.
A detailed assembly instruction in English with pictures is included.
Further repair guides, as well as help with fitting oil seals, can be found in the accessories section.
Quality product from the world's leading ball bearing manufacturer SKF.
Details
| Manufacturer | SKF |
| Material | Chrome steel (stainless steel) |
| Number of components | 2 pcs |
Suitable for the following models
| Universal | |
| Sachs | 50 (Fahrtwind, 1.25 / 1.5 PS, DE) 502 (Saxonette) - AL, AML 50/2 - L CH (0.8 PS), ML CH (0.8 PS), MB (2.6 PS), MLB (2.6 PS) 50/3 50/4 - MLFB (2.6 PS), LKH (4.5 PS) 503 - AAL, ABL, 2AL / 2BL, AB, AC, ADV 504 (ohne Tretwelle) 505 (mit Tretwelle) - 1A (AT), 2 A (HG) 508 - 1 A 535 |
| Pony / Cilo (Beta 521 & 512) | Beta 512 Beta 521 (Motor) |
| Piaggio | Ciao - Ciao, Ciao, Ciao, Ciao Si Bravo/Superbravo Boxer Grillo |
Accessories & related products
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Temperature resistance (min.): -60 - 315 °C · Manufacturer: Elring · Material: Silicone · Contents [ml]: 70 ml · Area of application: Chemistry · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Color: gray · Gap dimension (max.): 2 mm
CHF 19.90
CHF 284.29/l
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Temperature resistance (min.): -60 - 300 °C · Manufacturer: Elring · Contents [ml]: 70 ml · Area of application: Chemistry · Hazard warning: Causes serious eye irritation · Color: red · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Gap dimension (max.): 2 mm
CHF 22.90
CHF 327.14/l
Moped fans like you also bought:
Dell'Orto 50° carburetor elbow set M6x0.75
Manufacturer: Dell'Orto · Material: Brass · Surface: nickel-plated · Angle: 50 ° · Total length: 36.5 mm · Total length: 42 mm · Ø outside: 6 mm · Height: 40 mm · Height: 48 mm · Internal thread: MF5x0.75 (fine pitch thread) · Thread type: MF6x0.75 (fine pitch thread) · Width across flats nut: 7 mm
CHF 11.90
Speedometer 60 km/h Ø 48 VDO replica
Color: Chrome · Material: Metal · Material: Plastic · Color: beige · Color: black · Color: red · Surface: chrome-plated · Maximum speed: 60 Km/h · Lighting: Light slit · 4-edge speedometer cable: 2 mm · Ø outside: 53 mm · Ø Receptacle: 48 mm · Depth: 50 mm · Total height: 69 mm · Thread type: MF10x1 (fine pitch thread)
CHF 74.90
swiing® revival manual shift spring | Sachs 50/2, 503 2AL, 2BL (A1337)
Spring design: Tension spring · Total length: 28 mm · Length spring hook: 8 mm · Ø wire: 1.25 mm · Manufacturer: swiing® revival parts · Material: Spring steel · Surface: burnished · Color: gray · Ø inside: 6 mm · Ø outside: 8.5 mm · Pony spare part no.: A1337 · Sachs spare part no.: 0239 102 100
CHF 10.90
swiing® ingenious piston 40 mm | Cilo 502
Nominal diameter: 40 mm · Manufacturer: swiing® ingenious parts · Ø outside piston (A): 39.93 mm · Compression height (C): 27.9 mm · Curvature (D): 5.1 mm · Total piston height (E): 54 mm · Number of piston rings (F): 2 pcs · Piston ring mold: Rectangular ring · Piston ring impact: Flank safety device (FS) · Piston ring height: 2 mm · Thick piston ring: 1.65 mm · Ø piston pin (B): 12 mm · Weight: 93 g
CHF 69.90
Speedometer cable VDO (45 - 100 cm) black
Manufacturer: Made in Portugal · Thread type: MF10x1 (fine pitch thread) · Color: black · Outer shell length: 450 mm · Outer shell length: 500 mm · Outer shell length: 550 mm · Outer shell length: 600 mm · Outer shell length: 650 mm · Outer shell length: 700 mm · Outer shell length: 750 mm · Outer shell length: 800 mm · Outer shell length: 850 mm · Outer shell length: 900 mm · Outer shell length: 950 mm · Outer shell length: 1000 mm · 4-edge speedometer cable: 1.8 mm
CHF 8.90
Collection only possible with online purchase and appointment.
