Shaft repair sleeve which can be used on worn, scratched or run-in areas, e.g. on the crankshaft or pinion shaft.
If a shaft is heavily worn or scratched and can therefore no longer be properly sealed by the oil seal, this Speedi-Sleeve repair sleeve is used.
The 0.2 mm thick chrome steel sleeve is pressed over the shaft using the tool supplied.
Because the shaft is only applied a little, an oil seal with the original dimensions can still be used.
Shaft diameter: 17.0 mm
Width of usable running surface: 7.9 mm
Material: special, polished chrome steel
Installation instructions:
- Before installation, mount the crankshaft bearing on the shaft if necessary, as this can no longer be pressed over the shaft later.
- Clean the seal sliding surface on the shaft. Remove any unevenness with an abrasive cloth; the sleeve must not be positioned over keyways, holes, threads or other recesses
- Determine the installation position of the repair sleeve on the worn seal sliding surface and mark it precisely. The sleeve must completely cover the damaged area.
- Drive the repair sleeve onto the shaft with light, centric strokes against the impact cap. If the impact cap is too short, a piece of pipe can be used instead. The inside diameter should correspond to that of the impact cap. Ensure that the functional surface of the sleeve is not damaged.
- Do not use any heat during assembly; the use of adhesive is not necessary.
- In the case of large grooves or notches, the sleeve can be pressed on together with some permanently elastic sealing compound.
- If necessary, the flange can be removed by slitting the outer part and using needle-nose pliers.
- Then check everything again for damage and any burrs.
A detailed assembly instruction in English with pictures is included.
Further repair guides, as well as help with fitting oil seals, can be found in the accessories section.
Quality product from the world's leading ball bearing manufacturer SKF.
| Manufacturer | SKF |
| Material | Chrome steel (known as Nirosta®) |
| Number of components | 2 pcs |
| Universal | |
| Puch | E50 ZA50 (air-cooled) ZA50 (fan-cooled) Z50 (X30 Sport) Z50 (X30 Velux) 2-speed MS, MV, MV50 3-speed VSD, DS, VZ, MC |
| Sachs | 50/3 50/4 - MLFB (2.6 PS), LKH (4.5 PS) |
| Pony / Cilo (Beta 521 & 512) | Beta 512 Beta 521 (engine) |
| Tomos |
Accessories & related products
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Material: Silicone · Color: gray · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Contents [ml]: 70 ml · Area of application: Chemistry · Temperature resistance (min.): -60 - 315 °C · Gap dimension (max.): 2 mm
CHF 19.90
CHF 284.29/l
Dirko Dichtmasse rot (Silikon) Hochtemperatur 70 ml dauerelastisc
Temperature resistance (min.): -60 - 300 °C · Manufacturer: Elring · Contents [ml]: 70 ml · Area of application: Chemistry · Hazard warning: Causes serious eye irritation · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Gap dimension (max.): 2 mm · Color: red
CHF 22.90
Not in stock
CHF 327.14/l
Moped fans like you also bought:
swiing® revival 17" rear fender Inox | Puch Maxi N
Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Surface: polished · Color: Chrome · Folding the ends: closed folded · Folding the ends: not folded · Shape of the mudguard: angular · Mounting type: Nuts & bolts · Total length over ends: 625 mm · Scope: 940 mm · Wide mudguard profile: 82 mm · Height of mudguard profile: 35 mm · Total height from support surface to top edge: 285 mm · Wheel size [inch]: 17 "
CHF 37.90
Magura adjusting screw brake long
Manufacturer: Magura · Material: Brass · Surface: nickel-plated · Ø shaft: 6 mm · Thread type: MF6x0.75 (fine pitch thread) · Shank length: 11 mm · Total length: 47 mm · Total length: 65 mm · Drive: Knurled screw · Color: silver · Ø External head: 9.1 mm · Thread length: 24 mm
CHF 3.90
Motorex engine oil (gear oil) manual 450 ml
Manufacturer: Motorex · Viscosity (SAE): 80W · Oil type: GL4 · Gearbox type: Foot control · Gearbox type: Manual gearshift · Contents [ml]: 450 ml · Area of application: Gearbox lubrication with clutch · Temperature resistance (min.): -30 - 220 °C
CHF 9.90
CHF 22.00/l
Collection only possible with online purchase and appointment.
