Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and fan wheel. Suitable for your Puch X30 Velux moped / moped with Z50 engine.
The racing ignition comes complete with CNC-milled fan wheel and constantly supplies your cylinder with the optimum cooling.
With the two 100 g and 250 g additional weights (optional), you can increase the flywheel mass so that the engine runs more smoothly at idle and starting is easier when stationary. Depending on the application, the flywheel is supplemented with 100, 250 or 350 grams (both disks) of additional mass.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, thus smoother engine idling (382 grams)
- Finely balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set piston to TDC, marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel; this achieves a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good ground (earthing), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal plug:
- 1 = black
- 2 = blue
- 3 = white
Attention: Under no circumstances should excessively long screws be used to mount the fan wheel, as otherwise the stator winding may be damaged. A suitable screw set is included in the scope of delivery.
When purchasing this complete set, there is a substantial percentage off the retail price of the individual parts.
Exceptional product for the highest demands of the quality brand swiing®.
The set includes the following fixed parts:
Details
| Manufacturer | swiing® ingenious parts |
| Tension | 12 V |
| Light coil voltage | 12 V |
| Performance | 60 W |
| Direction of rotation | any |
| Ø mounting plate | 90 mm |
| Ø Internal flywheel | 63.5 mm |
| Ø Flywheel outside | 75 mm |
| Mounting type | Screws |
| Number of fixing points | 3 pcs |
| Area of application | Tuning, High End, Racing |
Suitable for the following models
| Puch | Z50 (X30 Velux) |
Accessories & related products
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Ø cable: 5 mm · Ø cable: 7 mm · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Component group Carburetor: Spraying · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
CHF 8.75
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Beta 521
Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Width across flats (trigger): 27 mm · Width across flats Screw: 19 mm · Manufacturer: GPO · Clamping depth: 10 mm · Strength class: 8.8 · Area of application: (Dis)assembly tool · Material: Steel · Surface: blackened · Number of components: 1 pcs · Total length: 55 mm · Total length: 75 mm
CHF 9.90
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Contents [ml]: 10 ml · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Type of application: 1K · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Temperature resistance (min.): -75 - 200 °C · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m · Area of application: Chemistry
CHF 21.90
CHF 2’190.00/l
swiing® ingenious fan wheel red (EVO, HPI, Bosch, Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: red · Ø outside: 120 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Number of fixing points: 10 pcs · Height: 13.5 mm · Weight: 87 g
CHF 62.40
swiing® ingenious fan wheel chrome (EVO, HPI, Bosch, Ducati) | Puch X30 Velux, Sachs 503, Belmondo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: chrome-plated · Color: Chrome · Ø mounting hole: 6 mm · Ø inside: 39 mm · Height: 13.5 mm · Weight: 87 g · Ø outside: 120 mm · Number of fixing points: 10 pcs · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm
CHF 68.90
DENSO (IWF24 / IWF27) Spark plug short thread U-Groove Iridium
Manufacturer: DENSO · Candle thread type: short · Thread type: MF14x1.25 (fine pitch thread) · Width across flats SW: 21 mm · Spark plug socket: M4 · Electrode material: Iridium · Suppressed: No · Area of application: Cross · Area of application: High End · Area of application: Tuning
CHF 25.90
Moped fans like you also bought:
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Ø nipple: 3.5 mm · Ø nipple: 6 mm · Manufacturer: Made in Germany · Area of application: Standard · Material: Steel · Surface: galvanized (blue) · Number of components: 1 pcs · Cable length: 2200 mm · Nipple length: 10 mm
CHF 2.40
swiing® revival ball bearing 14/27/6.3 coaster brake driver
Bearing type: Ball ring · Stock number: K1052 · Inner ring width: 7 mm · Ball bearing closed: No · Manufacturer: swiing® revival parts · Bearing clearance: CN (standard) · Bearing cage: "-" Sheet steel cage ball-guided · Ø ball: 6.34 mm · Groove ring: No · Surface: blank · Ø inside: 14 mm · Ø outside: 27 mm · Material: Steel
CHF 6.90
Fortune / Merrick 2.00 - 2.25 x 19" tube
Manufacturer: Fortune · Tire width [inch]: 2 - 2.25 " · Tire width [mm]: 50.8 - 57.15 · Width [inch]: 2 · Width [inch]: 2 1/4 · Tire height [%]: 100 · Old designation: 23 x 2 · Old designation: 23 x 2.25 · Valve type: TR4 Auto valve · Wheel size [inch]: 19 "
CHF 9.90
swiing® ingenious fan wheel black (EVO, HPI, Bosch,Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Ø inside: 39 mm · Ø outside: 120 mm · Height: 13.5 mm · Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: black · Ø mounting hole: 5.5 mm · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Number of fixing points: 10 pcs · Weight: 87 g
CHF 59.90
swiing® ingenious fan wheel red (EVO, HPI, Bosch, Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: red · Ø outside: 120 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Number of fixing points: 10 pcs · Height: 13.5 mm · Weight: 87 g
CHF 62.40
Collection only possible with online purchase and appointment.
