The Spark EVO Zero Basic module (version 2.0) was developed to make the breaker ignition on your Puch moped / moped significantly more wear-resistant and low-maintenance.
The box uses the breaker only as a clock generator and replaces the capacitor at the same time. Problems with worn breaker contacts and poor quality capacitors are therefore a thing of the past. In addition, your pulse coil can build up higher voltages, which has a positive effect on the upper speed limit of heavily tuned motors.
Advantages of the electronic ignition module:
- No wear
- Maintenance-free
- Higher voltage in the upper engine speed range
- Higher engine speeds possible than with conventional contact ignition
- Maintenance-free;
- Easy way to install a cut-off switch or kill switch
Mounting on ignitions with internal ignition coil:
- Mount the box close to the motor, e.g.B. on the motor screw
- Remove the capacitor from your contact ignition
- Remove the ignition coil cable from the capacitor, as well as the cable leading outwards inside your ignition;
- connect the cable of the interrupter with a new cable and lead this to the outside to the first connection of the module
- attach a new cable to the small cable of the ignition coil (e.g. the cable of the ignition coil).B. listed in the accessories) and route this to the outside to the middle connection of the module
- connect the right-hand connection to a ground point on the frame, e.g. on the motor screw
Installation for ignition systems with external ignition coil:
- Mount the box close to the external ignition coil, e.g. on the motor screw
- remove the capacitor from your contact ignition
- remove the cable of the pulse coil and the cable leading outwards inside your ignition from the breaker
- connect the breaker with a new cable and lead this outwards to the first connection of the module
- attach a new cable to the pulse coil (e.g. as described in the accessories manual).
- attach a new cable to the pulse coil (as listed in the accessories, for example) and route this outwards to the middle connection of the module
- Also attach the cable that leads to the external ignition coil to the middle connection of the module
- connect the right-hand connection of the module to a ground point on the frame, e.g. on the motor screw
- .e.g. on the motor screw
Notes: The breaker spacing can be left at 0.4-0.5 mm. Pay attention to the cable routing inside the ignition so that it is not damaged by the rotating flywheel. Your light coil supplies 6 V as before, so there is no need to convert your bulbs to 12 V. There is no need to flash off or adjust the preamplification.
You can find more parts for your ignition system on your Puch moped in the accessories section.
Quality product from the Italian manufacturer SparkEVO.
Details
| Manufacturer | SparkEVO |
| Mounting type | Tab for screwing |
| Connection type | Plug connection, Tab for screwing |
| Height | 33.5 mm, 15.3 mm |
| Ø mounting hole | 5.3 mm |
| Area of application | Tuning |
Suitable for the following models
| Puch |
Accessories & related products
Luster terminal 3-pole black small (0.1 - 2.5 mm²)
Cable cross-section: 0.1 - 2.5 mm · Number of connections: 6 pcs · Manufacturer: Made in Germany · Material: Brass · Material: Plastic · Material: Steel · Area of application: Workshop accessories · Total length: 18.5 mm · Color: black · Width: 22 mm · Height: 15.5 mm · Clamping diameter: 3.3 mm · Number of components: 1 pcs
CHF 1.40
Hot 
Leonelli 6V voltage regulator (1A quality)
Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: raw · Tension: 6 V · Mounting type: Screws · Type of current: Alternating current (AC) · Width: 27 mm · Performance: 50 W · Total length: 50 mm · Ø mounting hole: 6 mm · Height: 15 mm
CHF 29.90
HPI racing ignition 12V with light 60W
Manufacturer: HPI · Material: Aluminum · Material: Steel · Tension: 12 V · Ø Internal flywheel: 61.5 mm · Area of application: Tuning · Ø cable: 7 mm · Light coil voltage: 12 V · Performance: 60 W · Direction of rotation: left · Direction of rotation: right · Ø mounting plate: 90 mm · Ø Flywheel outside: 71.5 mm · Mounting type: Screws · Number of fixing points: 6 pcs · Weight: 340 g
CHF 299.90
swiing® revival cable repair set ignition
Cable cross-section [mm²]: 0.75 mm² · Cable cross-section [mm²]: 1 mm² · Ø single core: 0.15 mm · Manufacturer: swiing® revival parts · Material: Copper · Material: Plastic · Surface: raw · Color: black · Color: yellow · Total length: 300 mm · Number of cables: 2 pcs · Area of application: Standard · Ø outside: 1.9 mm
CHF 8.90
BOSCH Breaker without cable reinforced | Bosch / Ducati
Manufacturer: BOSCH · Material: Steel · Cable available: No · Ø mounting hole: 4.5 mm · Ø Internal flywheel: 90 mm · Ø axle: 4 mm · Area of application: Tuning · Number of fixing points: 1 pcs · Alternative version of the Pony OEM number: A4606 · BOSCH OEM number: 1 217 013 020 · Alternative version of the Sachs OEM number: 0983 106 000 · BERU OEM number: 0 340 100 466
CHF 20.90
Hot
VEC electronic ignition coil (replaces ignition coil, capacitor & contact breaker)
Place of use: Internal (in the ignition) · Manufacturer: VEC · Ø cable holder: 5 mm · Color: black · Mounting type: Screws · Total length: 77 mm · Cable length: 140 mm · Cable length: 420 mm · Ø mounting hole: 4.6 mm · Height: 48 mm · Ø Internal flywheel: 90 mm · Area of application: Original · Area of application: Performance · Area of application: Standard · Number of fixing points: 2 pcs · Hole spacing: 54 mm
CHF 99.90
Not in stock
Moped fans like you also bought:
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Ø cable: 5 mm · Ø cable: 7 mm · Pony OEM number: A2099 · Sachs OEM number: 0265 100 00
CHF 8.75
swiing® revival rubber grommet ignition | Puch X30 Z50
Manufacturer: swiing® revival parts · Material: Rubber · Surface: raw · Color: black · Width: 15.6 mm · Ø Cable bushing: 2.5 mm · Ø Cable bushing: 5.2 mm · Total length: 19.3 mm · Height: 3.5 mm · Area of application: Standard · Total height: 11.3 mm
CHF 7.90
Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing
Ø Stranded wire: 1.25 mm · Nipple shape: Cylinder · Ø nipple: 3 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Cable length: 2200 mm · Area of application: Standard · Number of components: 1 pcs · Nipple length: 5 mm
CHF 2.80
Fortune / Merrick 2.00-2.50 x 16/17" inner tube
Manufacturer: Fortune · Tire width [inch]: 2 - 2.5 " · Tire width [mm]: 50.8 - 63.5 · Width [inch]: 2 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Tire height [%]: 100 · Wheel size [inch]: 16 - 17 " · Wheel size [inch]: 17 " · Old designation: 20 x 2 · Old designation: 20 x 2.25 · Old designation: 20 x 2.5 · Old designation: 21 x 2 · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Valve type: TR4 Auto valve
CHF 9.90
Continental 2.25 x 17" KKS
Manufacturer: Continental · Tire width [inch]: 2.25 " · Tire width [mm]: 57.15 · Color: black · Width [inch]: 2 1/4 · Wheel size [inch]: 17 " · Old designation: 21 x 2.25 · Speed index: B = 50 km/h · Load capacity index: 39 = 136 kg · Profile type: KKS 10 · Tire type: Allround · White wall: No · Tubeless (yes/no): Tubetype TT (requires hose)
CHF 55.90
Collection only possible with online purchase and appointment.
