Reproduction of the original E50 engine housing with 4 bearings and kick starter for your Puch moped / moped.
The dimensions correspond to the original housing. This means that all add-on parts such as rods, end plates, crankshafts or cylinders can be used.
As with the original, a cylinder and pinion lock has been installed, which must be removed when fitting tuning parts.
The housing parts are numbered. The engine number can be stamped in by the owner if required.
Threaded stud bolt: M6x1 mm
Matching add-on parts and a racing gear for your Puch Maxi can be found in the accessories section.
Branded product from the manufacturer AKOA.
Suitable for the following models
| Puch | E50 |
Accessories & related products
GPO gasket set | Puch E50
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Area of application: Standard · Number of components: 7 pcs · Ø outlet inside: 19.9 mm · Hole spacing inlet: 32 - 38 mm · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Hole spacing outlet: 42 mm
CHF 9.90
Not in stock
swiing® revival set stud bolts M6 x 106 mm | Puch
Width across flats SW: 10 mm · Total length: 106 mm · Diameter: 5.9 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blue galvanized · Thread type: M6x1 (standard thread) · Drive: External hexagon · Thread length: 13 mm · Thread length: 18.5 mm · Alternative version of the Puch spare part no.: 360.1.10.034.1
CHF 7.40
swiing® revival crankshaft standard with mounted bearings (version 2.0) | Puch E50
Manufacturer: swiing® revival parts · Weight: 873 g · Area of application: Standard · Material: Steel · Cheek type: standard · Crankshaft stroke: 43 mm · Ø piston pin (B): 12 mm · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
CHF 134.90
swiing® revival 38 mm original cylinder 1.6 PS | Puch
Number of fixing points: 4 pcs · Manufacturer: swiing® revival parts · Material: Cast aluminum · Area of application: Standard · Camouflaged: Yes · Surface: sandblasted · Nominal diameter: 38 mm · Crankshaft stroke: 43 mm · Displacement: 50 ccm · Ø piston pin (B): 12 mm · Ø cylinder neck: 48 mm · Ø outlet inside: 19 mm · Ø Inlet inside: 9 mm · Hole spacing inlet: 38 mm · Thread inlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Outlet type: straight · Hole spacing outlet: 42 mm · Thread outlet: M6x1 (standard thread) · Alternative version of the Puch spare part no.: 349.7.10.105.0
CHF 109.90
CHF 139.90
Hot 
swiing® revival 38 mm original cylinder Vertex-Edition 1.6 PS | Puch
Number of fixing points: 4 pcs · Manufacturer: swiing® revival parts · Material: Cast aluminum · Area of application: Standard · Camouflaged: Yes · Surface: sandblasted · Nominal diameter: 38 mm · Crankshaft stroke: 43 mm · Displacement: 50 ccm · Ø piston pin (B): 12 mm · Ø cylinder neck: 48 mm · Ø outlet inside: 20 mm · Ø Inlet inside: 9 mm · Hole spacing inlet: 38 mm · Inlet window: 2 · Thread inlet: M6x1 (standard thread) · Hole pattern [mm]: 44 x 44 · Decompressor: Yes · Outlet type: straight · Hole spacing outlet: 42 mm · Thread outlet: M6x1 (standard thread)
CHF 149.90
Moped fans like you also bought:
NTN 6203 C3 Ball bearing 17/40/12
Bearing type: Deep groove ball bearing · Stock number: 6203 · Ø inside: 17 mm · Inner ring width: 12 mm · Ø outside: 40 mm · Manufacturer: NTN · Ball bearing closed: No · Width: 12 mm · Bearing clearance: C3 · Bearing cage: "-" Sheet steel cage ball-guided · Groove ring: No · Area of application: Standard · Material: Steel · Surface: blank
CHF 8.90
ESJOT sprocket 43 teeth galvanized | Puch Maxi, X30 NG-2AH
Chain pitch: 1/2" x 3/16" · Chain type: 415H · Number of fixing points: 6 pcs · Ø inside: 94 mm · Ø mounting hole: 6.7 mm · Manufacturer: ESJOT · Material: Steel · Surface: blue galvanized · Color: silver · Number of teeth: 43 pcs · Hole spacing 2: 68 mm · Hole spacing: 36.5 mm · Ø bolt circle: 106 mm · Cranking (offset): 8 mm
CHF 34.90
swiing® ingenious gasket outlet 28 mm graphite
Ø inside: 27.4 mm · Manufacturer: swiing® ingenious parts · Material: Graphite / Graphite · Area of application: Tuning · Reinforced: No · Ø outlet inside: 28 mm · Thickness: 3 mm · Place of use: Exhaust · Ø screw holder: 6.6 mm · Hole spacing outlet: 42.5 mm
CHF 7.40
Collection only possible with online purchase and appointment.
