HS-Retro countershaft 11 / 17 teeth (1A quality) | Puch X30 NS, NL

Cylindrical roller Ø 3.5x7.5 mm Gearbox | Puch Z50

Surface: Hardened · Manufacturer: Puch · Material: Steel · Area of application: Standard · Diameter: 3.5 mm · Width: 7.4 mm

Thrust washer 12.5/25/1.5 NOS | Puch M50, DSV, VZV

Thickness: 1.5 mm · Material: Steel · Surface: hardened & ground · Ø inside: 12.5 mm · Ø outside: 25 mm

swiing® revival thrust washer 12.5/18/2.2 gearbox | Puch Z50

Manufacturer: swiing® revival parts · Thickness: 2.25 mm · Material: Steel · Surface: hardened & ground · Ø inside: 12.5 mm · Ø outside: 18 mm

Thrust washer 12.5/18/2.75 Gearbox NOS | Puch Z50

Manufacturer: Puch · Thickness: 2.75 mm · Material: Steel · Surface: hardened & ground · Ø inside: 12.5 mm · Ø outside: 18 mm

swiing® revival thrust washer 12.5/18/1.6 gearbox | Puch Z50

Manufacturer: swiing® revival parts · Thickness: 1.6 mm · Area of application: Standard · Material: Steel · Surface: hardened & ground · Ø inside: 12.5 mm · Ø outside: 18 mm

swiing® revival thrust washer 12.5/18/1.8 gearbox | Puch Z50

Manufacturer: swiing® revival parts · Thickness: 1.8 mm · Area of application: Standard · Material: Steel · Surface: hardened & ground · Ø inside: 12.5 mm · Ø outside: 18 mm

HS-Retro shift sleeve Z50 (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Material: Steel · Recording type: Cross shot · Width: 8 mm · Ø inside: 13.35 mm · Ø outside: 43 mm · Puch spare part no.: 050.1.1410

HS-Retro bearing ring 24/32/7.5 large Z50 (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Width: 7.55 mm · Ø inside: 23.8 mm · Ø outside: 31.98 mm · Puch spare part no.: 329.1.13.065.1

HS-Retro bearing race 19.4/28.1/7.5 small Z50 (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Width: 7.5 mm · Ø inside: 19.44 mm · Ø outside: 28.1 mm · Puch spare part no.: 329.1.13.010.1

HS-Retro gearwheel 1st gear 28 teeth (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Material: Steel · Number of teeth: 28 pcs · Toothing type: straight toothed · Ø axle: 12.4 mm · Ø inside: 12.4 mm · Ø outside: 54 mm · Puch spare part no.: 350.1.13.011.1

HS-Retro gearwheel 2nd gear 23 teeth (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Material: Steel · Number of teeth: 23 pcs · Toothing type: straight toothed · Ø axle: 17.2 mm · Ø inside: 17.2 mm · Ø outside: 45 mm · Puch spare part no.: 350.1.13. 112.1

HS-Retro pinion shaft | Puch X30 NS, NL (1A quality)

Manufacturer: HS-Retro · Material: Steel · Surface: hardened & ground · Recording type: Interlocking · Total length: 90.5 mm · Ø outside: 12.35 mm · Ø outside: 16.75 mm · Puch spare part no.: 350.2.13.020.1

GPO clutch plates (pair) | Puch X30

Manufacturer: GPO · Area of application: Standard · Number of slats: 2 pcs

GPO sprocket 15 teeth (wide) | Puch

Manufacturer: GPO · Number of teeth: 15 pcs · Material: Steel · Chain type: 415H · Surface: Hardened · Recording type: Interlocking · Ø inside: 13.7 mm · Ø inside: 16.9 mm · Chain pitch: 1/2" x 3/16" · Total thickness: 4.6 mm

swiing® revival gasket set Z50 engine | Puch X30 NS / NL

Number of components: 10 pcs · Manufacturer: swiing® revival parts · Material: Sealing paper · Ø outlet inside: 22 mm · Hole spacing outlet: 42 mm · Hole pattern [mm]: 44 x 44 · Hole spacing inlet: 32 - 38 mm · Area of application: Standard

Nut flywheel M10x1 SW15 serrated

Width across flats SW: 15 mm · Drive: External hexagon · Thread type: MF10x1 (fine pitch thread) · Height: 10.5 mm · Ø outside: 19.8 mm · Area of application: Standard · Material: Steel · Surface: blue galvanized · Nut type: Flange nut

Motorex Automatic Motor Oil (ATF) 450 ml

Temperature resistance (min.): -45 - 200 °C · Manufacturer: Motorex · Oil type: ATF Dextron 3 (DEXIII) · Area of application: Gearbox lubrication with clutch · Contents [ml]: 450 ml · Gearbox type: Automatic machine · Pony spare part no.: A2080 · Sachs spare part no.: 0263 014 002

Clutch pressure plate | Puch E50 Cat. (LG1)

Material: Steel · Ø outside: 100 mm · Thickness: 2 mm

swiing® revival set stud bolts M6 x 106 mm | Puch

Manufacturer: swiing® revival parts · Thread length: 13 mm · Thread length: 18.5 mm · Diameter: 5.9 mm · Material: Steel · Surface: blue galvanized · Total length: 106 mm · Drive: External hexagon · Width across flats SW: 10 mm · Thread type: M6x1 (standard thread) · Alternative version of the Puch spare part no.: 360.1.10.034.1

GPO screws set engine mounting galvanized | Puch

Storage method: Sack · Manufacturer: GPO · Thread length: 23.5 mm · Area of application: Standard · Material: Steel · Surface: blue galvanized · Color: silver · Number of components: 12 pcs · Drive: External hexagon · Screw head: Hexagon · Width across flats SW: 13 mm · Shank: Yes · Strength class: 8.8 · Dimension storage box: 100 x 90 x 10 · Thread type: M8x1.25 (standard thread)

HS-Retro gearwheel 2nd gear 23 teeth (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Material: Steel · Number of teeth: 23 pcs · Toothing type: straight toothed · Ø axle: 17.2 mm · Ø inside: 17.2 mm · Ø outside: 45 mm · Puch spare part no.: 350.1.13. 112.1