HS-Retro gearwheel 2nd gear 23 teeth (1A quality) | Puch X30 NS, NL

Cylindrical roller Ø 3.5x7.5 mm Gearbox | Puch Z50

Width: 7.4 mm · Manufacturer: Puch · Material: Steel · Surface: Hardened · Area of application: Standard · Diameter: 3.5 mm

swiing® revival clutch & intermediate plate set (2 pcs.) | Puch Z50

Manufacturer: swiing® revival parts · Thickness: 1.5 mm · Thickness: 2.5 mm · Ø outside: 70 mm · Ø outside: 75 mm · Number of slats: 2 pcs · Ø inside: 46 mm · Ø inside: 51 mm

Thrust washer 12.5/25/1.5 NOS | Puch M50, DSV, VZV

Ø inside: 12.5 mm · Material: Steel · Surface: hardened & ground · Ø outside: 25 mm · Thickness: 1.5 mm

swiing® revival thrust washer 12.5/18/2.2 gearbox | Puch Z50

Ø inside: 12.5 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: hardened & ground · Ø outside: 18 mm · Thickness: 2.25 mm

Thrust washer 12.5/18/2.75 Gearbox NOS | Puch Z50

Ø inside: 12.5 mm · Manufacturer: Puch · Material: Steel · Surface: hardened & ground · Ø outside: 18 mm · Thickness: 2.75 mm

swiing® revival thrust washer 12.5/18/1.6 gearbox | Puch Z50

Ø inside: 12.5 mm · Manufacturer: swiing® revival parts · Area of application: Standard · Material: Steel · Surface: hardened & ground · Ø outside: 18 mm · Thickness: 1.6 mm

swiing® revival thrust washer 12.5/18/1.8 gearbox | Puch Z50

Ø inside: 12.5 mm · Manufacturer: swiing® revival parts · Area of application: Standard · Material: Steel · Surface: hardened & ground · Ø outside: 18 mm · Thickness: 1.8 mm

HS-Retro shift sleeve Z50 (1A quality) | Puch X30 NS, NL

Ø inside: 13.35 mm · Manufacturer: HS-Retro · Material: Steel · Recording type: Cross shot · Width: 8 mm · Ø outside: 43 mm · Puch spare part no.: 050.1.1410

HS-Retro bearing ring 24/32/7.5 large Z50 (1A quality) | Puch X30 NS, NL

Ø inside: 23.8 mm · Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Width: 7.55 mm · Ø outside: 31.98 mm · Puch spare part no.: 329.1.13.065.1

HS-Retro bearing race 19.4/28.1/7.5 small Z50 (1A quality) | Puch X30 NS, NL

Ø inside: 19.44 mm · Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Width: 7.5 mm · Ø outside: 28.1 mm · Puch spare part no.: 329.1.13.010.1

HS-Retro gearwheel 1st gear 28 teeth (1A quality) | Puch X30 NS, NL

Ø inside: 12.4 mm · Manufacturer: HS-Retro · Material: Steel · Toothing type: straight toothed · Ø axle: 12.4 mm · Number of teeth: 28 pcs · Ø outside: 54 mm · Puch spare part no.: 350.1.13.011.1

HS-Retro pinion shaft | Puch X30 NS, NL (1A quality)

Manufacturer: HS-Retro · Material: Steel · Surface: hardened & ground · Recording type: Interlocking · Ø outside: 12.35 mm · Ø outside: 16.75 mm · Total length: 90.5 mm · Puch spare part no.: 350.2.13.020.1

HS-Retro countershaft 11 / 17 teeth (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Material: Steel · Toothing type: straight toothed · Number of teeth: 11 pcs · Number of teeth: 17 pcs · Total length: 99 mm · Thread type: MF10x1 (fine pitch thread) · Puch spare part no.: 349.1.13.201.1

GPO clutch plates (pair) | Puch X30

Manufacturer: GPO · Area of application: Standard · Number of slats: 2 pcs

GPO sprocket 15 teeth (wide) | Puch

Chain pitch: 1/2" x 3/16" · Chain type: 415H · Manufacturer: GPO · Material: Steel · Surface: Hardened · Number of teeth: 15 pcs · Ø inside: 13.7 mm · Ø inside: 16.9 mm · Recording type: Interlocking · Total thickness: 4.6 mm

swiing® revival gasket set Z50 engine | Puch X30 NS / NL

Manufacturer: swiing® revival parts · Area of application: Standard · Material: Sealing paper · Ø outlet inside: 22 mm · Hole spacing inlet: 32 - 38 mm · Number of components: 10 pcs · Hole pattern [mm]: 44 x 44 · Hole spacing outlet: 42 mm

swiing® revival gearbox cover gasket (new model) | Puch Z50 engine

Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Width: 120 mm · Thickness: 0.35 mm · Number of fixing points: 7 pcs · Total length: 170 mm · Number of components: 1 pcs

Nut flywheel M10x1 SW15 serrated

Material: Steel · Area of application: Standard · Surface: blue galvanized · Nut type: Flange nut · Thread type: MF10x1 (fine pitch thread) · Drive: External hexagon · Height: 10.5 mm · Width across flats SW: 15 mm · Ø outside: 19.8 mm

Magura gas cable clamp / deco cable clamp Ø 5 x 6 mm

Total length: 6 mm · Manufacturer: Magura · Material: Brass · Material: Steel · Surface: nickel-plated · Number of components: 2 pcs · Thread type: M4x0.7 (standard thread) · Ø Cable bushing: 1.6 mm · Drive: Slot · Screw head: Lens head · Ø outside: 5 mm · Thread length: 4 mm

HS-Retro shift sleeve Z50 (1A quality) | Puch X30 NS, NL

Ø inside: 13.35 mm · Manufacturer: HS-Retro · Material: Steel · Recording type: Cross shot · Width: 8 mm · Ø outside: 43 mm · Puch spare part no.: 050.1.1410

HS-Retro gearwheel 1st gear 28 teeth (1A quality) | Puch X30 NS, NL

Ø inside: 12.4 mm · Manufacturer: HS-Retro · Material: Steel · Toothing type: straight toothed · Ø axle: 12.4 mm · Number of teeth: 28 pcs · Ø outside: 54 mm · Puch spare part no.: 350.1.13.011.1

HS-Retro pinion shaft | Puch X30 NS, NL (1A quality)

Manufacturer: HS-Retro · Material: Steel · Surface: hardened & ground · Recording type: Interlocking · Ø outside: 12.35 mm · Ø outside: 16.75 mm · Total length: 90.5 mm · Puch spare part no.: 350.2.13.020.1

HS-Retro countershaft 11 / 17 teeth (1A quality) | Puch X30 NS, NL

Manufacturer: HS-Retro · Material: Steel · Toothing type: straight toothed · Number of teeth: 11 pcs · Number of teeth: 17 pcs · Total length: 99 mm · Thread type: MF10x1 (fine pitch thread) · Puch spare part no.: 349.1.13.201.1