First gear transmission wheel for 2-speed manual Z50 engines from Puch X30 NS, NL mopeds / mopeds.
Number of teeth: 28
Toothing: straight
You can find thrust washers and other parts in the accessories section.
Original Puch spare part number: 350.1.13.011.1
Details
| Manufacturer | HS-Retro |
| Ø axle | 12.4 mm |
| Material | Steel |
| Number of teeth | 28 pcs |
| Toothing type | straight toothed |
| Ø inside | 12.4 mm |
| Ø outside | 54 mm |
| Puch spare part no. | 350.1.13.011.1 |
Suitable for the following models
| Puch | Z50 (X30 Sport) |
Accessories & related products
HS-Retro bearing ring 24/32/7.5 large Z50 (1A quality) | Puch X30 NS, NL
Ø inside: 23.8 mm · Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Width: 7.55 mm · Ø outside: 31.98 mm · Puch spare part no.: 329.1.13.065.1
CHF 58.70
HS-Retro bearing race 19.4/28.1/7.5 small Z50 (1A quality) | Puch X30 NS, NL
Ø inside: 19.44 mm · Manufacturer: HS-Retro · Area of application: High End · Area of application: Original · Material: Steel · Surface: hardened & ground · Width: 7.5 mm · Ø outside: 28.1 mm · Puch spare part no.: 329.1.13.010.1
CHF 44.90
HS-Retro countershaft 11 / 17 teeth (1A quality) | Puch X30 NS, NL
Manufacturer: HS-Retro · Material: Steel · Toothing type: straight toothed · Number of teeth: 11 pcs · Number of teeth: 17 pcs · Total length: 99 mm · Thread type: MF10x1 (fine pitch thread) · Puch spare part no.: 349.1.13.201.1
CHF 166.70
Moped fans like you also bought:
swiing® revival gasket set Z50 engine | Puch X30 NS / NL
Manufacturer: swiing® revival parts · Area of application: Standard · Material: Sealing paper · Ø outlet inside: 22 mm · Hole spacing inlet: 32 - 38 mm · Number of components: 10 pcs · Hole pattern [mm]: 44 x 44 · Hole spacing outlet: 42 mm
CHF 19.90
Not in stock
swiing® revival stud bolt set M6 x 106 mm | Puch
Total length: 106 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blue galvanized · Diameter: 5.9 mm · Thread type: M6x1 (standard thread) · Drive: External hexagon · Thread length: 13 mm · Thread length: 18.5 mm · Width across flats SW: 10 mm · Alternative version of the Puch spare part no.: 360.1.10.034.1
CHF 7.40
swiing® ingenious clutch spring reinforced +20% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30 mm · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Spring steel · Color: blue · Surface: coated · Total length: 20.5 mm · Ø outside: 39 mm · Number of components: 1 pcs
CHF 23.80
Collection only possible with online purchase and appointment.
